COVID-19, Advisory Services

Our people and our clients are our priority at WEW Engineering

While our offices will remain open, we are advising our staff to work from home, where possible, as per Government guidance with business continuing as normal.

All our staff members are fully contactable and fully available as required, via phone or email. Through our IT structure, we have the ability to work from home and can securely access our systems remotely.

The health and safety of our team and their families is paramount to us and we will do all we can to help to stop the spread of this virus.

Monitoring and response

Our priority is the health, safety, and wellbeing of our colleagues, partners, and clients. Please be aware that we are taking all necessary measures to reduce the risk of exposure to COVID-19. We will do our best to ensure there is no interruption to the service we provide to our clients.

Employee health

Following national guidelines, we have introduced a policy of self-isolation where necessary and we are taking advantage of secure home working as appropriate.

Meetings and site visits

Our position on general travel is that non-essential travel is not permitted until further notice.

We acknowledge that former routine visit to clients and other partners for meetings and presentations increases the risk of exposure to infection for everyone involved. We are implementing secure strategies and technologies to conduct meetings virtually, either via telephone or using video conferencing platforms.

As the situation develops

We continue to assess the situation and will update our policies and guidance accordingly. Please refer to the COVID-19 updates page on our website for the latest information.

We are willing to work together to contribute to everyone’s safety and to the effective management of this pandemic.  I hope you will inform us of any developments in your business that might affect us and we will continue to apprise you of any relevant developments in ours.

The application of Short Cut Nitrogen Removal in Industrial Wastewater Treatment


To date short cut nitrogen removal has been limited to the treatment of side stream flows from filtrate or centrate of anaerobically digested wastewaters, sludges, and landfill leachates. These flows have high ammonia levels and low levels of biodegradable COD. Traditionally biological nitrogen removal on mainstream wastewaters is achieved by nitrification and denitrification. This process is now well established and the modified Ludzack Ettinger process is most commonly used. There are however many industrial wastewaters that are high in total nitrogen relative to the amount of biodegradable COD and in these cases, there may not be enough biodegradable COD to achieve full nitrogen removal by the traditional process. However, it may be possible to use some of the other nitrogen removal paths that use less biodegradable COD and require less oxygen. This paper reviews how we can improve nitrogen removal by enhancing conditions to favour the short cut nitrogen routes.


Theoretical Background

Conventional Nitrification and Denitrification


The conventional nitrification and denitrification process for nitrogen removal utilises autotrophic bacteria in an aerobic environment to convert ammonia to nitrite then to nitrate. This is done by ammonia oxidising bacteria (AOB) and nitrite oxidising bacteria (NOB) respectively. Heterotrophic bacteria in an anoxic environment then convert the nitrate back to nitrite before converting the nitrite to nitrogen gas. This process relies on the addition of a lot of oxygen (energy) and carbon (BOD), it also produces a lot of sludge or volatile suspended solids (VSS).
The Modified Ludzack-Ettinger (MLE) process is designed to use nitrate produced by the aeration zone as an oxygen source for hetrotropic bacteria in the breakdown of raw wastewater in the anoxic basin. The influent wastewater return sludge from the clarifier, and nitrate-rich mixed liquor pumped from the effluent end of the aeration tanks are mixed together. The influent wastewater serves as the carbon source for bacteria, return activated sludge from the clarifier provides microorganisms, and the anoxic recycle pumps provide nitrate as an oxygen source. The anoxic basin is mixed, but not aerated.
The (MLE) process employs the conventional nitrification and denitrification process for nitrogen removal mention above.

Modified Ludzack-Ettinger process

Figure 1. Modified Ludzack-Ettinger process; source: Minnesota Pollution Control Agency, 2010.



The MLE process is relatively simple to control, maintaining the DO level in the aerobic zone is usually sufficient. The nitrate recycle and subsequent use of nitrate as an oxygen source reduces the oxygen requirements. The process will do more than just convert nitrogen compounds into nitrogen gas, the fact that it will produce a larger quantity of biomass than the nitrite shunt process means that soluble carbon, nitrogen and a small amount of phosphorus compounds will be converted into solid biomass which will, in turn, be separated in the clarifiers.


Suitability and Justification

In the MLE process, the anoxic tank is normally smaller than the aeration tank and the nitrate recycle flow is normally up to 5 times the raw wastewater flow.
The aeration tank is used to remove the last of the soluble BOD, and to convert the ammonia to nitrate.
In general, this process is only suitable for handling inlet nitrogen concentration of less than 100 mg/l.


Short Cut Nitrogen Removal

If the correct conditions can be created to favour the AOBs and inhibit the NOBs the nitrate stage of the process outlined above can be skipped. This is called nitritation-denitritation or more commonly as nitrite shunt (NS).
Although the biological denitrification takes place without extra oxygen being delivered, delivery of oxygen to the anoxic reactor at a reduced rate of the demand (50% to 70%), also referred as to aerated anoxic, leads to the process performance improvement. The NS may be followed by a second tank, where final simultaneous nitrification-denitrification (SND) polishing takes place to reduce ammonia, oxidised nitrogen and COD levels below licence limits.


Nitrite Shunt – Polishing Reactors – De-ammonification


Nitrite shunt process

Figure 2. Nitrite shunt process.


Skipping the nitrate stage reduces the oxygen and carbon requirements as well as reducing the sludge production.
• The nitrite shunt design will reduce the COD requirement for nitrogen removal by up to 40% compared to conventional nitrification and denitrification.
• The nitrite shunt design will reduce the oxygen required for nitrogen removal by up to 25%.
• The nitrite shunt will provide up to 40% reduction in the biomass production associated with denitrification.


Suitability and Justification

The nitrite shunt process requires more advanced process controls to create the optimum conditions for the AOBs and to, therefore, get the best ratio of AOB to NOB. The advantages listed above are very attractive especially if the raw wastewater is pre-treated using anaerobic digestion which removes a large portion of the carbon to produce biogas a renewable energy source.


The Nitrite Shunt and De-ammonification

It should be noted that it is also possible to convert ammonia direct to nitrogen gas using nitrite and the presence of Anommox bacteria. To date, this has been developed successfully by a number of specialist companies but again only for sidestream flows.
Theoretically, the nitrite shunt step and the de-ammonification step can be combined to allow removal of ammonia without the consumption of any carbon or biodegradable COD and with virtually no excess sludge production. This combined process step is available from a number of specialist companies. Patented and branded processes include:
• The DEMON SBR Process by DEMON Switzerland
• The SHARON Process by Sweco and Delft University
• The DeAmmon Process by Purac/Lacekby
• The ANITA Mox Process by Veolia
• The Cleargreen Process by Infilco Degremont
It is, however, possible to use standard process design and engineering to create conditions that will achieve the nitrite shunt process without the growth of Anommox bacteria.


Mainstream Nitrite Shunt Process Design and Control



The wastewater must be preconditioned to ensure that organic nitrogen is hydrolysed to ammonia. This often happens automatically in upstream sumps or balance tanks. This is a precondition for the removal of all organic nitrogen in all biological processes (all conventional plants).


Reactors and Clarifiers

As a minimum two main reactor tanks and a final clarifier are required to operate in series as shown.

Nitrate Shunt and Polishing Reactors

• The first reactor tank operates as the Nitrite Shunt Reactor.
• The second reactor tank operates as a polishing reactor.
• A Nitrite shunt clarifier may be added to separate the biomass and reduce the return of nitrite oxidising bacteria to the nitrite shunt reactor.


Process Control

The process performance relies on creating conditions that ensure the nitrite oxidising bacteria (NOB) are suppressed so that nitrite is not converted to nitrate in the first reactor.
Control parameters that help to suppress the growth of NOB bacteria in the nitrite shunt reactor are as follows:

Dissolved Oxygen: This should be maintained below 0.5 mg/l in general.

Reactor liquid temperature: The process is better suited to reactor operating in the range of 20 to 35 degrees C.

Total Ammonia Nitrogen: Residual total ammonia nitrogen (TAN)(sum of ammonium and ammonia) should be maintained above 1.0 mg/l as the AOB growth rate drops if the substrate ammonium levels are too low.

Transient Anoxia: Alternating anoxic and aerobic conditions are required and can be created by turning aeration equipment on and off and by the use of multiple raw wastewater feed points that can be opened and closed. Oxidation Ditches may be used to naturally create anoxic and aerobic zones.

Solids Retention Time (SRT): Low SRT can assist with the washout of NOB.

Ammonia-based aeration control: This is the simplest form of process control

AVN (ammonia versus nitrate) control: This is a more advanced form of process control. It comprises the following; An aerobic duration controller, A dissolved oxygen controller to maintain the DO at a set point during the aerobic period, An ammonia sensor and an oxidised nitrogen sensor. The ratio of ammonia to oxidised nitrogen is maintained constant. Set points are set for timers and sensors to ensure satisfactory operation.

Shortcut Nitrogen Removal

Figure 4. Shortcut Nitrogen Removal—Nitrite Shunt and Deammonification. Publisher: Water Environment Federation


Microbiology and Laboratory Support

Our ability to identify the different bacteria has increased and two techniques are now available namely
Fluorescence in Situ Hybiridization (FISH)

Quantitative real-time polymerase chain reaction analysis.
These techniques can be used to confirm that the AOB bacteria are relatively abundant and that the NOB bacteria are suppressed. (pPCR).


Nitrite Shunt Application

While many new plants may benefit from a complete Nitrite Shunt and De-ammonification process step, many new and existing plants will benefit from the application of nitrite shunt process and downstream polishing reactors only.
It is especially suitable where the readily biodegradable COD to Nitrogen ratio is between 4.0 and 2.0 and where the wastewater temperature is above 20 °C.
There are many existing plants with multiple reactors tank that can be modified to improve the level of nitrogen removal.
Typical existing Industrial WWTPs include:

Dairy plants with an upstream anaerobic stage. Brewery plants with an upstream anaerobic stage. Pharmaceutical plants with high nitrogen levels. Landfill Leachate Plants.

If you need Innovative Water, Energy or Wastewater Solutions

Contact Us